add an outdoor outlet. - outdoor weatherproof box

by:Hanway     2019-09-17
add an outdoor outlet.  -  outdoor weatherproof box
The 5 ways to get power where you need it are not complicated.
But get the wire to the right place. -
No wall tearing-
It could be a big challenge.
In this article, we will help you choose the best strategy to locate and power your new outlet.
We will not discuss in depth about how to install the socket box or the connecting line.
Water machine, go to familyhandy-man.
And search for "outlet ".
"There you will find instructions for adding outdoor outlets on the wall or on the pillars in the yard, as well as detailed wiring diagrams.
We will show you some different cabling techniques that you can use to power your new socket and tell you the pros and cons of each.
As with any electrical project, be sure to talk to the local electrical inspector about what licenses and inspections are needed before starting.
Strategy 1 laying the cable edge support beam from the basement or crawl space is a wide plate located on the base and supporting the exterior wall.
If your basement ceiling is not finished, it is a simple project to install a socket on the edge pallet.
But there are few things to pay attention.
If you want to put the exit on the edge of the beam parallel to the floor beam, make sure you can enter the space from the basement.
Sometimes the beam is too close to be accessible.
If you want to add the exit to the edge beam on the floor beam, make sure that the outlet is close to the entrance to the beam space so that you do not drill to the end of the beam. Use a long 1/8-
In, a bit or part of a hard clothes rack, drill the positioning hole where you want it.
Then you can see from the inside if the location of your choice is easy to reach.
If you have a crawling space or an unfinished basement, you may have to remove the insulation, and in the old house, even pry the concrete or rubble through the edge of the beam, which is the best way.
The choice of power supply and socket location is unlimited, which is easy.
Good access to rim joist near the new exit.
Starting with the RIM pallet, it is usually easy to connect the new cable to the circuit breaker panel or the existing basement lighting circuit.
If the circuit is in an unfinished basement or crawl space, AFCI protection does not have to be added.
This option is one of the easiest options if you don't have an unfinished basement or crawl space.
You just need to find a location outside the house with a socket inside.
You can then fish new wires from the internal outlet to the external outlet.
But keep in mind that you may have to add AFCI protection if AFCI does not exist.
Please confirm with your electrical inspector.
This is an article in familyhandyman.
Com that provides details-
Add information about outdoor outlets using this technology.
Search for "outdoor outlets ".
"Through the wall, you can run the line from an internal socket without tearing the wall apart.
But this approach limits your choice: your external outlet must be within a few inches of the existing internal outlet.
Strategy 3 if you don't have a basement or crawl space, running the cable from the attic is a great option to deliver power to an external outlet without going through the wall.
Basically, you put the UFIDA cable through a hole in the floor, through the attic to reach your power supply, leaving enough cable to reach the new outdoor outlet, plus an extra foot.
You then slide the connection over the cable with a sleeve until the pipe extends a pan into Sofen.
To complete, connect the box to the wires of the pipe, the attached tape, and the new socket.
The insulation and the narrow space make it a nuisance for the wires to go through the attic.
Consider this option as a last resort.
Here are some tips for running the cable: * choose a position for the outlet that is not so conspicuous with the lower spray or exterior trim, the vertical pipe. * Use UF (
Underground feeder)
Cable, unconventional NM (nonmetallic).
* Connect the pipe to the bell box with waterproof compression fittings instead of fixing screws-
Pipe connector.
* Install the sleeve on the top of the Pipe sleeve to protect the sharp edge of the pipe.
If there is no other option, you can run the UF cable up and down from the attic, through the attic, through the sleeves on the wall and down to your new exit.
Strategy 4 if you have an existing external outlet and don't mind the appearance of the surface, run the pipeline from the existing outlet
Install the pipe, this is a good choice to add the socket.
If your existing socket is surface mounted, you can simply remove a counterfeit from the weatherproof box and connect the pipe to the rainproof fitting.
But if your socket is recessed, you have to add a weatherproof box extension to allow the connection.
Turn with a pipe using LB accessories.
For more information on the use of metal or plastic pipes, please go to the home handyman.
And search for "pipes ".
"The outlet to access another extension pipe from an existing outlet is a good way to add another outlet without running a new cable through a wall, basement or attic.
You can lay the pipe under the side plate or near the ground so that it will not be so conspicuous.
Strategy 5 run underground cables from existing outlets. This option is similar to No.
4 above, but you can run underground to the new exit, not on the surface of your house.
Depending on the depth you want to dig, you can also choose to deal with underground lines.
The easiest way is not to lay pipes underground.
Instead, it uses a UFIDA cable buried in 12. deep.
However, there are also some precautions.
Cables must be protected by aGFCI.
If the existing socket does not have GFCI protection, simply replace it with a GFCI socket.
In addition, you must protect the cable from the outlet box to the depth of 12 in with a plastic or metal sleeve.
Under the ground.
You can run post in your yard using the same method (
Go find a family handyman.
Com and search for "outdoor outlets ").
You can run power underground if you don't want to run exposed pipes. A 12-in. -
You only need deep trench for UFIDA cable.
Jeff Gordon editor @ Family Handyman.
Custom message